Fix Huawei Nova 10 SE IMEI (BNE-LX1) Free

Fix Huawei Nova 10 SE IMEI (BNE-LX1) Free

Restore IMEI on Huawei Nova 10 SE (BNE-LX1) The 2026 Solution

The Huawei Nova 10 SE is a sleek device, but like many modern Androids, it can suffer from critical software glitches. One of the most alarming issues users face is a sudden loss of network signal accompanied by a missing or invalid IMEI. This usually isn't a hardware failure; it is a corrupt partition in the modem's file system.

While traditional methods often require expensive hardware boxes or full firmware flashes (which can brick the phone), technicians are now turning to a streamlined software approach. This guide walks you through the latest method using the DT Pro (DFT Pro) utility to repair the NV data and restore your connectivity without deep-level soldering.

Key Features of This Repair Method

• Software-Focused: No need to replace the motherboard or UFS chip.
• EDL Mode Support: Uses the standard Emergency Download mode via test points.
• Selective Repair: Repairs only the modem partition, keeping user data relatively safer than a full factory reset.
• Cost-Effective: Utilizes the DT Pro tool, removing the need for paid unlock credits.
• Hidden Menu Integration: Uses the built-in Huawei Project Menu to finalize the restoration.

Requirements and process

Before we proceed, ensure you have the following ready. Skipping these steps increases the risk of failure.

1. Device: Huawei Nova 10 SE (Model BNE-LX1).
2. PC: A Windows computer (Win 10/11 recommended).
3. Software: DT Pro (or DFT Pro) installed with drivers.
4. Hardware: A standard USB data cable and a pair of tweezers (for shorting).
5. Data Backup: Backup all important data, as opening the device carries slight risk.

Phase 1: Accessing EDL Mode and Safety Backup

Never start a repair job without a safety net. If the process is interrupted, you need a way to restore the phone to its current state.

1. Hardware Access and Test Point Shorting

1. Discharge Static: Touch a metal object to discharge static electricity from your hands.
2. Open the Device: Power off the phone. Carefully open the back cover to access the motherboard.
3. Identify Test Points: Look for the two small metal contacts on the PCB marked for EDL mode.
4. Shorting: Use metal tweezers to connect these two points while plugging in the USB cable.

Figure 1: The internal circuit board of the Huawei Nova 10 SE. Red arrows indicate the specific test points that must be shorted to force the device into Emergency Download (EDL) mode.

2. Establishing Connection and Backup

Once the device is connected and recognized by your PC as a Qualcomm port:

1. Launch Tool: Open DT Pro on your computer.
2. Device Detection: Navigate to the Huawei section. The software should display your device details, such as the Model and Android version, confirming a successful connection.
• 
• Figure 2: The DT Pro interface detecting the BNE-LX1. Note the 'Recovery Tools' module on the left, which is used for reading and writing critical partitions.
3. Create Backup: Before proceeding, click on the option to create an EFS Backup.

Why This Step is Critical:

Imagine a technician accidentally flashes the wrong file to a client's phone. Without the backup created in this phase, the phone becomes a hard brick ("Paperweight"). With the backup, it takes mere minutes to undo the mistake.

Phase 2: Patching the Software

Once your backup is secured, we will inject the necessary files to restore the IMEI configuration.

1. Selecting the Repair File

1. Locate File: Using the file explorer inside the tool or your desktop, locate the specific BNE-LX1 repair patch you downloaded.

Figure 3: The desktop view showing the selection of the patch file. Ensure you select the file specifically labeled for the BNE-LX1 model to avoid compatibility issues.

2. Flashing the Partitions

1. Initiate Flash: With the file selected, click Start Flash or Write.
2. Partition Manager: The software will now scan the device. You will see a list of partitions, including sds, pers, and nvmf. The tool will automatically write the necessary data to these specific sectors.
• 
• Figure 4: The partition manager displaying the internal storage structure of the device. The tool targets these specific sectors to repair the IMEI configuration.
3. Completion: Wait for the "Success" log. Do not disconnect the cable until the process is 100% complete.

Phase 3: Finalizing via Secret Code

Now that the base software is patched, we need to assign the valid IMEI number to the modem using Huawei's hidden engineering menu.

1. Boot Up: Disconnect the cable and power on the Huawei Nova 10 SE normally.
2. Open Dialer: Tap the phone icon as if you are making a call.
3. Enter Code: Type the following string exactly: ##2846579##
4. Access Menu: A hidden Project Menu will appear.
5. Navigate: Select ProjectMenu > HUAWEI OEMINFO > Special Task.
6. Input IMEI: Choose the option to Restore/Write IMEI. A dialog box will appear prompting for input.
• 
• Figure 5: The input screen asking for IMEI details. Note that for this specific model, writing to IMEI 2 is often the key step to restoring network connectivity.
7. Save & Restart: Enter the original IMEI from your box sticker, tap OK, and reboot the device.

Verification

After the phone restarts, go to Settings > About Phone > Status.

1. Check if the IMEI number is visible (no longer "Unknown" or "Invalid").
2. Insert your SIM card.
3. You should see signal bars appear within 30 seconds. The modem will automatically latch onto the carrier network.

BNE_OEM_PERSIST

Frequently Asked Questions

Is this method free?

Yes, this specific guide utilizes the free functions of the DT Pro tool. However, ensure you have the necessary drivers installed, which are also available publicly.

Do I need to open the phone every time?

For the initial repair via EDL mode, yes, you must open the phone to short the test points. If you were simply restoring a backup later, you might not need to, but for repairing a corrupt IMEI, EDL access is required.

What happens if I write the wrong IMEI?

You must always write the IMEI that corresponds to the device's hardware (printed on the box/label). Writing a random IMEI is illegal in many jurisdictions and can lead to network blacklisting.

Will I lose my photos?

The method described involves flashing a patch which generally targets the modem partition. However, because EDL mode operations are low-level, there is always a risk of data loss. We strongly recommend backing up photos and documents before starting.

Loading Older Post...

OLDER POST